doc. no : qw0905-la38b-76/y-s1-pf rev : c date : data sheet ligitek electronics co.,ltd. property of ligitek only led array la38b-76/y-s1-pf 25 - aug. - 2008 lead-free parts pb
+ - note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. ly4840-pf package dimensions part no. page ligitek electronics co.,ltd. property of ligitek only 25.0min 1.0min 2.54typ 0.5 typ 3.8 1.0 1.5max 3.0 3.8 la38b-76/y-s1-pf 1/5 10.0 2.54typ + - 5.2 0.5 typ 1.0 3.8 3.0 3.8 3.5 0.3 note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice.
ratings -40 ~ +85 spectral halfwidth nm -40 ~ +100 note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. typical electrical & optical characteristics (ta=25 ) property of ligitek only part no la38b-76/y-s1-pf color yellow diffused gaasp/gap yellow material emitted 58535 lens peak wave length pnm parameter peak forward current duty 1/10@10khz power dissipation reverse current @5v operating temperature forward current storage temperature tstg t opr ir symbol i f pd i fp absolute maximum ratings at ta=25 2.6 1.7 8.0 12 max. forward voltage @20ma(v) min. luminous intensity @10ma(mcd) min. typ. 130 viewing angle 2 1/2 (deg) 10 a unit 20 60 80 y ma ma mw page 2/5 la38b-76/y-s1-pf part no.
fig.3 forward voltage vs. temperature fig.5 relative intensity vs. wavelength ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 fig.4 relative intensity vs. temperature ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage f o r w a r d c u r r e n t ( m a ) forward current(ma) fig.2 relative intensity vs. forward current r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0101001000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40-200204060 1.0 1.1 1.2 500550600650 0.0 0.5 1.0 2.03.04.05.0 80100 0.8 0.9 -20 -40 40 20 080100 60 2.0 0.0 0.5 1.0 1.5 2.5 3.0 700 y chip page 3/5 la38b-76/y-s1-pf part no.
dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to case) note: 1.wave solder should not be made more than one time. 2.you can just only select one of the soldering conditions as above. 50 0 0 preheat 25 120 2 /sec max 150 time(sec) 100 5 /sec max 260 c3sec max 260 temp( c) soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time only) distance:2mm min(from solder joint to case) 2.wave soldering profile ligitek electronics co.,ltd. property of ligitek only page 4/5 60 seconds max la38b-76/y-s1-pf part no.
this test intended to see soldering well performed or not. this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. the purpose of this test is the resistance of the device under tropical for hours. solder resistance test 1.t.sol=260 5 2.dwell time= 10 1sec. 1.t.sol=230 5 2.dwell time=5 1sec solderability test thermal shock test 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles 1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs high temperature high humidity test mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 mil-std-202:103b jis c 7021: b-11 ligitek electronics co.,ltd. property of ligitek only this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) low temperature storage test 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) high temperature storage test operating life test reliability test: test condition test item description mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 mil-std-883:1008 jis c 7021: b-10 jis c 7021: b-12 reference standard 5/5 page la38b-76/y-s1-pf part no.
|
